Team3S: 3000GT & Stealth Saturday, December 8 2001
Volume 01 : Number
694
----------------------------------------------------------------------
Date:
Fri, 7 Dec 2001 14:36:56 -0800
From: "Bob Forrest" <
bf@bobforrest.com>
Subject: Re:
Team3S: Keyless Entry Remote
From: "Will Fortenberry" <
BigWill_VR4@hotmail.com>
> I
have a '94 VR-4. Is there any reason I can't use a '95 and up keyless
entry
remote on my '94? Can anyone confirm if they are compatible?
> Thanks for
your time,
> Will
- -------------------------->
When I
ordered keyless remotes (I got a spare) a couple of years ago, the
dealer did
not differentiate between the model years, so I assume that they
are the same
for all our cars. Photo (and programming instructions) are on
our
website:
www.Team3S.com/FAQkeyless.htmBest,
Forrest
***
Info:
http://www.Team3S.com/Rules.htm
***
------------------------------
Date: Sat, 8 Dec 2001 09:31:28
-0500 (EST)
From:
kimbyrd@webtv.net
(Kimberly Byrd)
Subject: Team3S: rear view defogger/rear wiper
Hey,
guys!
I have a little bit of a problem with my 1994 3000GT. My rear
view
defogger doesn't work even though the dash light comes on. Also, my
rear
view wiper system will spray water, but the wipers won't run. I
don't
see fuse for either in the panel at my feet. Any ideas on how to
fix
this? Thanks, Kim
*** Info:
http://www.Team3S.com/Rules.htm
***
------------------------------
Date: Sat, 8 Dec 2001 15:05:34
-0600
From: "xwing" <
xwing@wi.rr.com>
Subject: Re: Team3S:
injectors measurements
Mikael:
Stock injector, measured by micrometer
in inches (eyeball approximated mm)--
Body length = 2.858"
(~72.5mm)
Diameter of plastic injector tip = 0.36" (~9.1mm)
Barrel
diameter at lower gasket = 0.63" (~16mm)
Barrel diameter at largest diameter
= 0.95" (~24mm)
Diameter of upper tip which inserts into fuelrail = 0.41"
(~10.3mm)
Diameter of upper tip's gasket groove = 0.304" (~7.8mm)
Jack
T.
From: "Mikael Kenson" <
vr4@bahnhof.se>
Sent: Friday, December
07, 2001 3:10 PM
Subject: Team3S: injectors measurements
> Can someone
please measure the stock injectors?
> I need to know total length, with of
top and tail. (In mm if possible)
> Thanks
*** Info:
http://www.Team3S.com/Rules.htm
***
------------------------------
Date: Sat, 8 Dec 2001 15:20:59
-0800 (PST)
From: Jeff Lucius <
stealthman92@yahoo.com>
Subject:
Re: Team3S: injectors measurements
Jack and I came up with almost
identical numbers (measured with dial
micrometer in inches):
Total
length 2.856 in, ~72.54 mm
Top feed diameter 0.412 in, ~10.47 mm
Feed
opening 0.174 in, ~4.2 mm
O-ring diameter ~0.450 in, ~11.43 mm
Bottom
diameter 0.360 in, ~9.14 mm
Web page with pics:
http://www.geocities.com/lutransys/jlucius3/j3-2-inj360.htmJeff
Lucius,
www.stealth316.com- ---
xwing <
xwing@wi.rr.com>
wrote:
> Mikael:
> Stock injector, measured by micrometer in inches
(eyeball
> approximated mm)--
>
> Body length = 2.858"
(~72.5mm)
> Diameter of plastic injector tip = 0.36" (~9.1mm)
>
Barrel diameter at lower gasket = 0.63" (~16mm)
> Barrel diameter at
largest diameter = 0.95" (~24mm)
> Diameter of upper tip which inserts
into fuelrail = 0.41" (~10.3mm)
> Diameter of upper tip's gasket groove =
0.304" (~7.8mm)
>
> Jack T.
>
> From: "Mikael Kenson"
<
vr4@bahnhof.se>
> Sent: Friday,
December 07, 2001 3:10 PM
> Subject: Team3S: injectors
measurements
> > Can someone please measure the stock
injectors?
> > I need to know total length, with of top and tail. (In
mm if
> possible)
> > Thanks
*** Info:
http://www.Team3S.com/Rules.htm
***
------------------------------
End of Team3S: 3000GT &
Stealth V1
#694
***************************************